The long awaited BME680 from Bosch gives you all the environmental sensing you want in one small package. This little sensor contains temperature, humidity, barometric pressure, and VOC gas sensing capabilities. All over SPI or I2C at a great price! Like the BME280 & BMP280, this precision sensor from Bosch can measure humidity with ±3% accuracy, barometric pressure with ±1 hPa absolute accuracy, and temperature with ±1.0°C accuracy. Because pressure changes with altitude, and the pressure measurements are so good, you can also use it as an altimeter with  ±1 meter or better accuracy! The BME680 takes those sensors to the next step in that it contains a small MOX sensor. The heated metal oxide changes resistance based on the volatile organic compounds (VOC) in the air, so it can be used to detect gasses & alcohols such as Ethanol, Alcohol and Carbon Monoxide, and perform air quality measurements. Note it will give you one resistance value, with overall VOC content, but it cannot differentiate gasses or alcohols. Please note this sensor, like all VOC/gas sensors, has variability and to get precise measurements you will want to calibrate it against known sources! That said, for general environmental sensors, it will give you a good idea of trends and comparisons. We recommend that you run this sensor for 48 hours when you first receive it to "burn it in", and then 30 minutes in the desired mode every time the sensor is in use. This is because the sensitivity levels of the sensor will change during early use, and the resistance will slowly rise over time as the MOX warms up to its baseline reading. For your convenience we've pick-and-placed the sensor on a PCB with a 3.3V regulator and some level shifting, so it can be easily used with your favorite 3.3V or 5V microcontroller. Specifications Resources Datasheet Library Sample Code Tutorial

Details: Output: red dot (650 nm). Size: Φ 12.0x35mm. line length: about 135mm. Net weight: 13.5g. Voltage: 3.0 v-5 v. Current: 40 mA (maximum). Purpose: industrial positioning.   Applications: It can be used to aim for positioning Can be used for laser test instruments Can be used for concentricity positioning Can be used for positioning medical equipment Can be used for signal equipment production Specifications Resources Datasheet  

Metal alloy mechanical arm with 6 Degree Of Freedom. The kit is delivered in a simple carton. The subassemblies are packaged in separate bags. The structural elements of the robotic arm are made by stamping aluminum plate. To give a better appearance and deburr the edges, the pieces are sandblasted. Black anodising (visible on the assembly instructions) has been abandoned.  Positive point of this kit, we find very easily spare parts. Most structural elements, servo motors MG996R, flanged base, clamp (or claw) are standard elements that are found very often our store. This kit with 4x MG996R Servo Motors, and 2x DS3115MG Servo Motors NOTE: Use DS3115MG Motors for high load sections on the Robot Arm. Specifications of DS3215 (15kg-cm Large Torque Digital  Servo): Stall Torque (5V): 19 kg/cm (263.8oz/in) Stall Torque (6.8V):  21.5 kg/cm (298.5 oz/in) Speed : 0.16 sec/60°(5V) / 0.14 sec/60°(6.8V) Operating Voltage: 4.8 ~ 6.8 DC Volts Dead band: 3μs     Weight: 60 g (2.12 oz) Motor Type: DC Motor Gear Type: Copper & Aluminum Working frequence: 1520μs / 333hz Size: 40 x 20 x 40.5 mm ( 1.58 x 0.79 x 1.60 in) Specifications of MG996R: Dimension : 40mm x 19mm x 43mm Net weight: 69g Color: Black Operating Speed : 0.17sec / 60 degrees (4.8V no load) Operating Speed : 0.13sec / 60 degrees (6.0V no load) Stall Torque : 13 kg-cm (180.5 oz-in) at 4.8V Stall Torque : 15 kg-cm (208.3 oz-in) at 6V Operation Voltage : 4.8 - 7.2Volts Gear Type: All Metal Gears Resources Tutorial 

A carefully designed mobile power supply for your Arduino / Raspberry Pi projects. The mobile power is stacked on the for Arduino board and powered via the 5V/GND pin. We also provide a USB-A output interface that you can use to connect to other devices using a USB cable. The charging interface is micro USB, and any standard Micro USB charger can be used to charge the module. Lithium Battery Model: 16340Charging current: 500mADischarge current: 1000mAFeature:1. Adapter 16340 lithium battery2. 5V and 3.3V dual output3. Built-in lithium battery protection IC with overcurrent, overvoltage, undervoltage and short circuit protection4. Built-in battery anti-reverse protection5. The toggle switch can freely turn the output Specification Charging interface: Micro USB (Android port)Charging voltage: 4.5V -5.5VCharging current: 580mA maxOutput interface: 2.5mm header and standard USB socket5V output current: 1.3A max3.3V output current: 1.0A maxCharging indicator: red light during charging, full green lightProduct size: 60mm * 28mm * 16mm(L * W * H)

This product is based on the WIFI Kit 32 added SX1278 chip (alternate for SX1276), that is, LoRa remote modem, 868MHz frequency, about -139dBm high sensitivity, +20 dBm power output, high reliability, transmission distance (measured open area communication distance 3.6Km). Onboard 32MByte Flash, Wi-Fi antenna, 0.96-inch blue OLED display, lithium battery charging circuit and interface, CP2102 USB to serial chip, the perfect support for Arduino development environment, can be very simple and fast for program verification and product development. Features: Frequency: 868MHz Operating voltage: 3.3V to 7V. Operating temperature range: -40 ° C to + 90 ° C. Supports Sniffer, Station, softAP and Wi-Fi Direct modes. Transmit power: 19.5 dBm @ 11b, 16.5 dBm @ 11g, 15.5 dBm @ 11n. Data rate: 150 Mbps @ 11n HT40,72 Mbps @ 11n HT20,54 Mbps @ 11g, 11 Mbps @ 11b. Receiver sensitivity up to - 139 dBm. UDP continues to throughput by 135 Mbps. Package Contains: 1x LORA Module 2x Dupont Headers 1x U.FL Antenna

The mobile power is stacked on the for Arduino board and powered via the 5V/GND pin. It has a USB-A output interface that you can use to connect to other devices using a USB cable. The charging interface is micro USB, and the charging tool is convenient to obtain (such as: for Android mobile phone adapter). When it is stopped, it is recommended to turn off the power output and let the mobile power supply enter the standby state, thus saving limited battery energy.   It uses 16340 lithium battery (battery not included), the shield works with one or two batteries. Two 16340 lithium batteries (depending on the battery capacity) has about 1500mAH capacity.   Lithium Battery Model: 16340 Charging current: 500mA Discharge current: 1000m Specifications

These 9 Element, 96mm Mecanum wheels are heavy duty, offering an individual load capacity of up to 4 Kgs. They come in left and right pair, and with a hex couple of your choice. And 4 wheels can carry a load of up to 16 Kgs. Package contains 2x Mecanum wheels, 2x Hex Coupler and mounting screws. Dimensions: Inner diameter: 6.5mm Outer diameter: 96mm Thickness: 45mm Material:Plastic Colour: Black

This kit includes dual 5mm thick acrylic sheets with four high torque encoder gear motors and mecanum wheels. The chassis provides enough space to add sensors like LiDAR or camera for computer vision, as well as a computer like Raspberry Pi or Nvidia Jetson or an Arduino MCU and batteries. Mecanum wheels are very useful to increase the maneuverability of a robot. These wheels come with 45º rollers that move independently and allows the robot to move forward, backward, sideways, diagonally or spin in place. But please, don’t make the confusion with omnidirectional wheels. Mecanum wheels are different than omnidirectional wheels, but the result is almost the same. Depending on which wheels rotate in which direction, the robot will change the heading or spin in place. The motors have attached encoders. Having encoders, you can add an IMU sensor and create a map of the room. This makes it easier to transform this chassis into an autonomous robot, that is able to navigate on smooth surfaces in an apartment, building or factory floor. Mecanum wheels have some disadvantages compared with the “normal” wheels that we’re using for our cars or shopping carts. These wheels tend to wander side-to-side when the robot is trying to negotiate an inclined floor. Also, mecanum wheels are known for losing traction.   Motor Parameters: Model: GB37-520 Speed: 330RPM Rated current: ≤0.7A Rated voltage: DC12V Rated power: ≈ 7.2W Length L: 58mm Diameter R: 37mm Maximum encoder accuracy: 1320CPR

This is a 3-axis palletizing mechanical arm with a vacuum pump that is ideal for pick and place applications. With 3x 20 Kg servos, this robot can easily move up to 500 grams of objects which has a flat surface for attaching to the suction cup. Combined with the servo control board, this is your ideal choice for building assembly line style projects. Specifications Material: Aluminum alloy Tube:Silicone Size: as showm Weight: about 950g Servo: DS3218 & MG90 Controller not included