0.36" 6-Digit 7-Segment LED Display Module
This is a basic 6-digit 7-segment display module with TM1637 controller. The display shows each decimal point. The module can be controlled with two IO pins.
For use with Arduino, use library: TM1637.h
Nixie tube: 0.36 inches
Driver IC: TM1637
Display size: 46x14 mm
Voltage: 5 volts
1x TM1637 LED Display Module
High quality, solid metal case
Deliver high efficiency and constant power for a stable flight
Low noise, low starting voltage, and low energy consumption
Highly reliable and durable for long-lasting use
Lightweight, easy to install
Suitable for Tiny Whoop
Package contains: 2CW 2CCW
Designed for RC Racing Quadcopter
Operating Voltage 1.5-3.7V
Max. Thrust:15g (Direct Drive)
Load Current: 1.0A at 3.7V (Direct Drive)
Lifetime Rating: 5-6 hours
Shaft Diameter: 0.8mm
Shaft Length: 5mm
Wire Length: 70mm
Material: Plastic & Metal
Can Size: 15x6x6mm/0.6x0.2x0.2inch
Net weight: 8g
GND: power supply
VCC: DC 3.3-5V
SCL: SPI Clock Cable
SDA:SPI Data Cable
DC: SPI Choice/ Command Choice
BLK:Backlight control, default floating, low level off
The TFT display provides a semiconductor switch for each pixel and each pixel is directly controlled by pulse. Therefore, each node is relatively independent and can be continuously controlled, which not only improves the response speed of the display, but also can be accurately controlled. The color level is displayed to make the TFT LCD color more realistic, the brightness is good, the contrast is high, the layering is strong and the color is bright.
Viewing direction: IPS
LCD Size: 1.3 inch
Resolution: 240*240 ( There are two display way: horizontal display and vertical display, you can adjust the display direction. )
Interface: SPI Interface, 7PIN
Color: TFT Full Color - 65k Colors
IC Driver: ST7789
Working temperature: -20-70℃
Working Voltage: 3.3V
Display area Size: 23.4*23.4mm
TFT Module Size: 27.78* 39.22mm
Resolution: 128 pixels X 64 pixels
Super wide viewing angle: more than 160 °
Ultra-low power consumption: normal display 0.08W (far below the TFT display)
Wide supply range: DC 3V-5V (without any changes, directly compatible with common 3.3V and 5V power supply system)
Industrial grade: Operating temperature range -30 degree~ 70 degree
Dimensions: (length) 35.4MM * (W) 33.5MM * (thickness) 4.3MM
Support for multiple operating modes: 3-wire SPI, 4 wire SPI, IIC
With chip select CS signal, you can achieve multiple SPI or IIC device on the same bus work
Compatible with 3.3V and 5V control chip I / O level
OLED screen, internal drive chip: SH1106 (Operation and SSD1306 same)
1.3" I2C OLED
Pin 1 - GND
Pin 2 - VCC
Pin 3 - SCL
Pin 4 - SDA
1.3" SPI OLED
Pin 1 - GND
Pin 2 - VCC
Pin 3 - CLK / SCL
Pin 4 - MOSI / SDA
Pin 5 - Reset (Reset Control Signal for OLED Display Module)
Pin 6 - DC (Command / data selection control signal of OLED)
Pin 7 - CS (Chip selection control signal of OLED)
This is a dot matrix 128x64 COG graphic type OLED module. The size of the active area is 1.54” diagonal with module dimension 42.04 x 27.22 mm.
This 1.54 inches OLED module has built-in IC SPD0301, and boasts high contrast ratio 10,000 : 1, operating in 7 Pin SPI format.
Size: 1.54 inch
Resolution: 128 X 64
Display Color: Yellow/ Blue/ White
Driving IC: SPD0301; compatible with SSD1309
Voltage: 3.3V - 5V
SPI Interface Definition:
Pin 1 - GND (power ground)
Pin 2 - VCC (power positive)
Pin 3 - CLK / SCL (clock)
Pin 4 - MOSI / SDA (data)
Pin 5 - RES (reset)
Pin 6 - DC (data/command)
Pin 7 - CS (chip selection, if not used, it can be directly connected with ground)
Package includes: 1x 1.54inch OLED Display Module SPI Interface 3.3-5V SSD1309 (Yellow/ Blue/ White)
Input voltage range: 2.5V~VOUT-0.5V
The output voltage can be set to 5V/8V/9V/12V, the default is 12V
Output performance: Take 3.7V lithium battery input as an example, it can output 5V 1.2A, 8V 0.7A, 9V 0.6A, 12V 0.5A. Make sure that the input current and output current does not exceed 1.5A.
Voltage setting description
The front side of the PCB can be seen with the words A and B. The output voltage can be changed by using the soldering iron to change the pad on and off. In the following table, 0 means the pad is disconnected and 1 means the pad is connected.A B VOUT0 0 5V0 1 8V1 0 9V1 1 12VThe pad next to the LED indicator can also be turned off to turn off the indicator.
Product size: 22mm × 11mm × 3.6mm
10 Separately Controlled LED's
High-Intensity Green Output
Ideal for Audio and Meter Displays
Easy to Mount
LED Size: 2 x 5 mm
Absolute Maximum Ratings
Power Dissipation (Pd): 65 * 10 mw
Forward Current (If): 25 mA
Peak Forward Current (Ifp): 250 mA
Electro-Optical Data (@ 10 mA)
Forward Voltage - Typical: 1.85 V
Forward Voltage - Maximum: 2.2 V
Luminous Intensity Typical: 120 Mcd
Working Voltage: DC 12V - DC 40V.
Control Power:0.01 - 400W.
Current: Rated 8A, Max 10A.
Static Current:0.02 A ( Standby ).
PWM Duty Cycle:10% -100%.
PWM Frequency:13 KHz.Material: Plastic, metal.
Size (L*W*H): 6cm x 5.5cm x 2.8cm/2.36"x 2.16"x1.10"(approx)
4 hole diameter: 3 mm(approx)
Control the speed of a DC motor with this controller.
High efficiency, high torque, low heat generating.
With reverse polarity protection, high current protection.
5mm high brightness piranha 12 LEDs
Long lifetime, low consumption, very convenient to use
Light board four corners with a fixed screw hole, easy fixed
Input voltage: DC 3.5-5.5V (Recommended 5V DC)
Operating current: about 200MA
Power: about 1W
Light Color: White
Dimension: Approx. 45 x 28 x 10mm (L*W*H)
A crystal oscillator, is an electronic oscillator circuit that uses the mechanical resonance of a vibrating crystal of piezoelectric material to create an electrical signal with a very precise frequency.
Stability in frequency.
Small in size.
Easy of interfacing.
Clock generator for microcontroller.