Servo Motors

The TowerPro SG90 mini servo is lightweight, high-quality and lightning-fast. The servo is designed to work with almost all radio control systems. The SG90 mini servo with accessories is perfect for R/C helicopter, plane, car, boat and truck use. It equips Carbon Fiber Gears which makes the servo motor much lighter than the same metal gear motor. For small load applications using the metal gear, servo motor adds on unnecessary weight, so we suggest using these lightweight plastic gear servo motors. The TowerPro SG90 9g Mini Servo is a 180° rotation servo. It is a Digital Servo Motor that receives and processes PWM signal faster and better. It equips sophisticated internal circuitry that provides good torque, holding power, and faster updates in response to external forces. Micro Size Servo Speed (sec/60deg): 0.10/4.8V Torque (Kg-cm): 1.80/4.8V Size (mm): 23.1mm x 12.2mm x 29mm C/W plastic horn and accessories Pulse Width: 500-2400 µs Rotation Angle: 180 degree Specifications Model SG90 Weight(gm) 9 Operating Voltage 3.0 – 7.2 V Operating Speed @4.8V 0.10sec/60° Stall Torque @4.8V 1.2 kg-cm Stall Torque @6.6V 1.6 kg-cm Operating Temperature (°C) -30 to 60 Dead Band Width 7 μs Gear Type Glass Fiber Rotational Degree 180 Servo Plug JR Cable Length 25 cm Length (mm) 22.8 Width (mm) 12.6 Height (mm) 34.5 Shipment Weight 0.125 kg Shipment Dimensions 6 × 6 × 4 cm   Resources Datasheet Library Sample Code Tutorial  

Add more power to your robot with this metal-geared MG90S servo. The tiny little servo can rotate approximately 90 degrees (45 in each direction), and works just like the standard kinds you're used to but smaller. You can use any servo code, hardware or library to control these servos. Good for beginners who want to make stuff move without building a motor controller with feedback & gear box, especially since it will fit in small places.  Please note, this servo will 'hold' the position even when no signal is sent!To control with an Arduino, we suggest connecting the orange control wire to pin 9 or 10 and using the Servo library included with the Arduino IDE. Position "0" (1.5ms pulse) is middle, "90" (~2ms pulse) is all the way to the right, "-90" (~1ms pulse) is all the way to the left. NOTE: Operating servos at or near Stall Torque is not recommended and will shorten the life of your servo drastically. Specifications Weight: 13.4g Dimension: 22.8mm X 12.2mm X 28.5mm Stall Torque: 1.8kg/cm (4.8V); 2.2kg/cm (6.6V) Operating Speed: 0.10sec/60degree (4.8V); 0.08sec/60degree (6.0V) Operating Voltage: 4.8V ~ 6.6V Temperature range: 0℃ to 55℃ Dead Band Width: 1us Power Supply: Through External Adapter Servo Wire Length: 25 cm Servo Arms & Screws included Resources Datasheet Library Sample Code Tutorial  

This mini 2-axis FPV (First Person View) Pan-Tilt Kit pairs with our TowerPro SG90 mini servo for creating your own anti-vibration camera gimbal.  PV Nylon Head Two Axial plastic Two axial platform Anti-vibration lightweight Good design and shape Sophisticated products Provision to add standard servo motors (sold separately) Pan and tilt using simple PPM interface using RC servos with position control. 180 Degree of freedom on both axis. Supported Motors: TOWERPRO SG90, TOWERPRO MG90S  No Servo Included Specifications Material Plastic Color Black Weight (gm) 20 Shipment Weight 0.1 kg Shipment Dimensions 7 × 7 × 6 cm   Tutorial  

MG996R is an upgraded version of MG995 servo. The new PCB and IC control system which makes it far more accurate. Its internal gearing and motor are also upgraded to improve dead bandwidth and centering. It is a great choice for 1/10 buggy and airplane helicopter, RC-cars from 10 to 6-th scale truggy and monster and many RC model. This high-torque standard servo now comes in a metal-gear flavor, for extra-high torque (9.4 kg-cm!) and reliability! It can rotate at least 180 degrees (90 in each direction) with a classic 1.5-2.5ms pulse. You can use any servo code, hardware or library to control these servos. To control with an Arduino, we suggest connecting the orange control wire to pin 9 or 10 and using the Servo library included with the Arduino IDE. Position "0" (1.5ms pulse) is middle, "90" (~2ms pulse) is all the way to the right, "-90" (~1ms pulse) is all the way to the left. The default servo pulse widths (usually 1ms to 2ms) may not give you a full 360 degrees of motion. In that case, check if you can set your servo controller to custom pulse lengths and try 0.75ms to 2.25ms. You can try shorter/longer pulses but be aware that if you go too far you could break your servo! NOTE: Operating servos close to or at stall torque reduces their life and will permanently damage them beyond repair. Specifications Weight: 55g Dimension: 40.7mm X 19.7mm X 42.9mm Stall Torque: 9.4 kg-cm (4.8V); 11 kg-cm (6V) Operating Speed: 0.23sec/60degree (4.8V); 0.2sec/60degree (6.0V) Operating Voltage: 4.8V ~ 6.6V Gear Type: Metal gear Temperature Range: 0℃ - 55℃ Dead Band Width: 1us Servo Wire Length: 32cm Current Draw at idle: 10mA No Load Operating Current: 170mA Stall Current: 1.4A Servo Arms and Screws included Resources Datasheet Library Sample Code Tutorial  

This lightweight (2g) anodized aluminum servo disc works with the 25T servo splines that are typically found on standard-size servos and can be used as a stronger replacement for the plastic horns often included with these servos. 25T Spine for Futaba and Power HD Servos Adjustable type servo arm Hard anodized finish Material: CNC Aluminum Size (D): 20mm (approx.) single disc Specifications

This lightweight (5g) anodized aluminum servo horn works with the 25T servo splines that are typically found on standard-size servos and can be used as a stronger replacement for the plastic horns often included with these servos. The portion that grips the spline can flex to accommodate slight differences in spline diameters, and the included screw can then be used for adjustments. The two general-purpose mounting holes are threaded for M3 screws. 25T Spine for Futaba and Power HD Servos. Adjustable type servo arm Hard anodized finish Includes two steel bolts to secure the split-clamp onto the servo output M3 threads for your car or helicopter joints Material: CNC Aluminum Size (L x W x H): Approx. 35 x 15 x 6mm / 1.4 x 0.6 x 0.2inch Specifications   Tutorial  

The 1501 MG is a metal-geared analog servo from Power HD that delivers extra-high torque normally associated with much more expensive or larger servos. This is one of our most popular standard-size servos. Servo horns and associated hardware are included. The HD-1501 MG is a powerful standard-size servo that features metal gears and two ball bearings and can deliver a tremendous amount of torque for such a high-speed servo. The 1501 MG works with standard RC servo pulses, providing a running angle of approximately 165° over a servo pulse range of 800 µs to 2200 µs, and it has a 10″ (25 cm) cable that is terminated with a standard JR-style connector, which is Futaba-compatible. The default servo pulse widths (usually 1ms to 2ms) may not give you a full 180 degrees of motion. In that case, check if you can set your servo controller to custom pulse lengths and try 0.75ms to 2.25ms. You can try shorter/longer pulses but be aware that if you go too far you could break your servo! NOTE: Operating servos close to or at stall torque reduces their life and will permanently damage them beyond repair.   Weight: 63g Dimension: 40.7mm X 20.5mm X 39.5mm Stall Torque: 15.5 kg-cm (4.8V); 17.0 kg-cm (6V) Operating Speed: 0.16sec/60degree (4.8V); 0.14sec/60degree (6.0V) Operating Voltage: 4.8V ~ 6.6V Bearing Type: Ball Bearing x 2 Motor Type: DC Motor Gear Type: CopperTemperature Range: -20℃ - +60℃ Working Frequency：1520μs / 50Hz Servo Wire Length: 32cm Current Draw at idle: 10mA No Load Operating Current: 170mA Stall Current: 1.2A Servo Arms and Screws included Specifications Resources Datasheet Library  Sample Code Tutorial  

This high-torque standard servo now comes in a metal-gear flavor, for extra-high torque (10 kg*cm!) and reliability! It can rotate at least 120 degrees (60 in each direction) with a classic 1.5-2.5ms pulse, but if you can extend your pulses it can go up to about 170 degrees - it varies a bit servo-to-servo. You can use any servo code, hardware or library to control these servos. To control with an Arduino, we suggest connecting the orange control wire to pin 9 or 10 and using the Servo library included with the Arduino IDE. Position "0" (1.5ms pulse) is middle, "90" (~2ms pulse) is all the way to the right, "-90" (~1ms pulse) is all the way to the left. The default servo pulse widths (usually 1ms to 2ms) may not give you a full 180 degrees of motion. In that case, check if you can set your servo controller to custom pulse lengths and try 0.75ms to 2.25ms. You can try shorter/longer pulses but be aware that if you go too far you could break your servo! NOTE: Operating servos close to or at stall torque reduces their life and will permanently damage them beyond repair.  Specifications Weight: 55g Dimension: 40.7mm X 19.7mm X 42.9mm Stall Torque: 9.4 kg-cm (4.8V); 11 kg-cm (6V) Operating Speed: 0.20sec/60degree (4.8V); 0.16sec/60degree (6.0V) Operating Voltage: 4.8V ~ 6.6V Gear Type: Metal gear Temperature Range: 0℃ - 55℃ Dead Band Width: 1us Servo Wire Length: 32cm Current Draw at idle: 10mA No Load Operating Current: 170mA Stall Current: 1.2A Servo Arms and Screws included Resources Datasheet Library  Sample Code Tutorials

It is upgraded version of TowerPro MG945 with the new PCB and IC control system which makes it  more accurate. Its internal gearing and motor are also upgraded to improve dead bandwidth and centering. This high-torque standard servo now comes in a metal-gear flavor for extra-high torque (13 kg-cm) and reliability! It can rotate at least 180 degrees- 90 in each direction, with a classic 1.5-2.5 ms pulse. You can use any servo code, hardware or library to control these servos. For Arduino controls, we suggest connecting the orange control wire to pin 9 or 10 and using the Servo library included with the Arduino IDE. Position "0" (1.5 ms pulse) is middle, "90" (~2 ms pulse) is all the way to the right, "-90" (~1 ms pulse) is all the way to the left. The default servo pulse widths (usually 1 ms to 2 ms) may not give you a full 180 degrees of motion. In that case, check if you can set your servo controller to custom pulse lengths and try 0.75 ms to 2.25 ms. You can try shorter or longer pulses but be aware that if you go too far you could break your servo! NOTE: Operating servos close to or at stall torque reduces their life and will permanently damage them beyond repair.   Weight: 55g Dimension: 40.7mm X 19.7mm X 42.9mm Stall Torque: 10.5 kg-cm (4.8V); 13 kg-cm (6V) Operating Speed: 0.20sec/60degree (4.8V); 0.17sec/60degree (6.0V) Operating Voltage: 4.8V ~ 6.6V Gear Type: Metal gear Temperature Range: 0℃ - 55℃ Dead Band Width: 1us Servo Wire Length: 32cm Current Draw at idle: 10mA No Load Operating Current: 170mA Stall Current: 1.2A Servo Arms and Screws included Specification Resources Datasheet Library Sample Code Tutorial  

The DS3218 is a large torque digital servo with precision potentiometers, offering stable, low noise operation. It is IP66 waterproof ideal for operations under water splash. These are built with high-precision metal gears with hard anodizing, CNC aluminium middle Shell, and dual ball bearings. Features: High performance digital standard servo High-precision metal gears with hard anodizing CNC aluminium middle Shell Dual ball bearings Operating Voltage: 4.8 ~ 6.8 DC Volts Dead brand: 3μs Weight: 60 g (2.12 oz) Motor Type: DC Motor Gear Type: Copper & Aluminum Working frequence: 50-333Hz Operating travel:180°（PWM 500-2500μs）  OR 270°（PWM 500-2500μs） Size: 40 x 20 x 40.5 mm ( 1.58 x 0.79 x 1.60 in) Package Included: 1x Digital Servo 1x 25T Adjustable metal servo arm

The Parallax Standard Servo is ideal for robotics and basic movement projects.  It can hold any position over a 180-degree range and is easily interfaced with any Parallax microcontroller. Key Features: Holds any position between 0 and 180 degrees 38 oz-in torque at 6 V Accepts four mounting screws High precision gear made of the POM (polyacetal) resin makes for smooth operation with no backlash Weighs only 1.55 oz (44 g) Note: Servo current draw can spike while under load. Be sure that your application's power supply and voltage regulator is prepared to supply adequate current for all servos used. Do not try to power this servo directly from a BASIC Stamp module's Vdd or Vin pins; do not connect the servo's Vss line directly to the BASIC Stamp module's Vss pin. Specifications: Power Requirements: 4 to 6 VDC*, Communication: Pulse-width modulation Gear material: Acetal copolymer Dimensions: 2.2 x 0.8 x 1.6 in (55.8x 19 x 40.6 mm) excluding servo horn Operating temp range: +14 to +144 °F (-10 to +50 °C) Torque: 38 oz-in @ 6 V Resources: Cad FileSpin CodeStamp CodeServo Dimensions Product details Tutorials: ProjectUsageArduino Tutorial

This high-torque standard servo now comes in a metal-gear flavor, for extra-high torque (10 kg-cm!) and reliability! It can rotate at least 180 degrees (90 in each direction) with a classic 1.5-2.5ms pulse. You can use any servo code, hardware or library to control these servos. To control with an Arduino, we suggest connecting the orange control wire to pin 9 or 10 and using the Servo library included with the Arduino IDE. Position "0" (1.5ms pulse) is middle, "90" (~2ms pulse) is all the way to the right, "-90" (~1ms pulse) is all the way to the left. The default servo pulse widths (usually 1ms to 2ms) may not give you a full 180 degrees of motion. In that case, check if you can set your servo controller to custom pulse lengths and try 0.75ms to 2.25ms. You can try shorter/longer pulses but be aware that if you go too far you could break your servo! NOTE: Operating servos close to or at stall torque reduces their life and will permanently damage them beyond repair. Specifications Weight: 55g Dimension: 40.7mm X 19.7mm X 42.9mm Stall Torque: 10 kg-cm (4.8V); 12 kg-cm (6V) Operating Speed: 0.23sec/60degree (4.8V); 0.2sec/60degree (6.0V) Operating Voltage: 4.8V ~ 6.6V Gear Type: Metal gear Temperature Range: 0℃ - 55℃ Dead Band Width: 1us Servo Wire Length: 32cm Current Draw at idle: 10mA No Load Operating Current: 170mA Stall Current: 1.2A Servo Arms and Screws included Resources Datasheet Library Sample Code Tutorial  

This high-torque standard servo can rotate approximately 180 degrees (90 in each direction). You can use any servo code, hardware or library to control these servos. Good for beginners who want to make stuff move without building a motor controller with feedback & gear box. Comes with 3 horns, as shown.To control with an Arduino, we suggest connecting the orange control wire to pin 9 or 10 and using the Servo library included with the Arduino IDE. Position "0" (1.5ms pulse) is middle, "90" (~2ms pulse) is all the way to the right, "-90" (~1ms pulse) is all the way to the left. Note that the default servo pulse widths (usually 1ms to 2ms) may not give you a full 180 degrees of motion. In that case, check if you can set your servo controller to custom pulse lengths and try 0.75ms to 2.25ms. You can try shorter/longer pulses but be aware that if you go too far you could break your servo! NOTE: Operating servos close to or at stall torque reduces their life and will permanently damage them beyond repair. Specifications Weight: 47g Dimension: 40.6mm X 20.5mm X 38mm Stall Torque: 5.5 kg-cm (4.8V); 6.511 kg-cm (6V) Operating Speed: 0.19sec/60degree (4.8V); 0.56sec/60degree (6.0V) Operating Voltage: 4.8V ~ 6.6V Gear Type: Metal gear Temperature Range: 0℃ - 55℃ Dead Band Width: 1us Servo Wire Length: 32cm Current Draw at idle: 10mA Servo Arms and Screws included Resources Datasheet Library Sample code Tutorial