- Simple structure and lightweight, CNC aluminum alloy structure- Brushless motor direct drive- With anti-vibration rubber balls, easy to adjust- Compatible with Gopro 4 3, 2,1- With 3pcs 2804 160t motor- With 32bit Storm32 firmware gimbal controller, sensor- With motor protector which can help heat dissipation
Strom32 Gimbal ControllerFeatures:- The controller can be used for building high-quality 3-axis camera stabilizing systems that can be mounted to UAV and for building handheld camera stabilizers.- This version of the controller is our new direction in the development of stabilizing solutions.- It will replace the previous 8-bit version of the SimpleBGC controller, keeping 100% back-compatibility, but adding the new functionality.- 32-bit MCU — ARM Cortex M4.- Effectively calculates the complex tasks for 3-axis stabilization,700 times/seconds gyro calculates- Allows camera control with the RC or analog joystick.- Use several switchable profiles for different modes of operation- Control Pitch or roll by PWM or receiver, supports a variety of RC protocols: PWM, Sum-PPM, Spektrum, and s-bus.- Use IMU1 and onboard IMU2 dual sensor module lock YAW accurately, stable performance- Support follow mode, lock mode, absolute mode, or speed mode.
- Power supply: 9-15V(3-4S)- Drive current: Max.1.5A- Height: 11cm- Color: Black
Upgrade to high-quality brushless PTZ control panel, chips are original chip, increase the supply anti-reverse polarity protection, counter-power to prevent customers from unintentional indirect cause significant damage.
Original sensor chip, better accuracy, and change the sensor interface, the connection is more solid, easy to lose, iic error does not occur; Upgrade the roof, increasing the head hook hole, easy to use PTZ hook.
You can use the remote real-time control of pitch and roll angleExtended function: to set flip, installed on fixed wing; Handheld PTZ can be changed; (user to modify, we does not provide technical support). Can be upgraded to three PTZ (user to modify, we do not provide technical support)
Notes:1. Recommended power supply for the gimbal is 12V. (3cell lipo battery)2. The gopro camera must fasten on the gimbal. (Not any loose, this is very important)3. Adjust the gopro camera left or right, let the camera almost at level.4. Please do not power on the gimbal until the Gopro camera is fixed on the gimbal.
Name: CNC metal brushless gimbal
Material: CNC Aluminium alloy
Motor: Model 2208 kv80 Brushless motor
Control Panel: BGC3.0 Brushless control panel
Strap: for Gopro camera strap
Compatible camera: for GOPRO 3 3+ 4
Battery plug type: JST plug / XH-2.54 plug
Voltage: 12V/3cell Lipo battery
Compatible model: for DJI phantom I, II and other DIY drones
Color: black Silver
Size: 80 x 80 x 80mm
Package size: 125 x 125 x 105mm
It is a osd video overlay module that combine OSD Signal and Camera Video Signal.
It is compatible with Mini Pix / Pixhawk flight controller, to get the flight datas.Besides, it has USB Port to connect computer and then can configurate via RadioLinker OSD_Tool appSpecification:Item Name: Mini OSD Module for Mini PIX / Pixhawk Flight ControllerHow to configure1. Connect this Mini OSD Module to computer via Andriod USB Cable.2. Open Configuration APP " RadioLinker OSD_Tool"3. Find " OSD_Config" from file and then double click to enter into " MinimOSD_18.104.22.168"4. Comes into configuration Page ( Operation like Picture 5 showed on product page )If you also connect other modules, pls find the right CMO Port as following steps.( A. Open " my computer " B. get" device manager "C. then choose COM Port from " Serial Port".D. Finally, choose same COM on configuration page.)5. Setting parameter and Save. ( Picture 6 Showed )- A. Choose the data you want to get by left sheet.- B. Drag the mouse and then can move the data's showing position to right side.- C. After setting parameter, click " File" and " Save OSD file " .- D. If you need same setting, just find " File" and " Open OSD file", then it can show.6. Change Language. ( Like Last photo showed )
Voltage: 5-12vDimensions: 50 x 18 x 10mmWeight 4g
This 1500TVL CMOS Camera can be used as both PAL and NTSC. The toggle switch is provided on the camera for switching between PAL and NTSC.
This camera is very compact and easy to use. This camera is tailored for FPV which offers delicate clear image, micro ultralight design, high definition color.
Image Sensor: 1/3" Mg SUPER HAD II CCD
Horizontal Resolution: 1500TVL
S/N Ratio: >600dB (AGC Off)
Electronic Shutter Speed: 1/50 ~ 100,000 (PAL), 1/60 ~ 100,000 (NTSC)
Autogain Control (AGC): Low/Middle/High
Backlight Compensation: Yes
Min. Illumination: 0.001 Lux / 1.2F
Power: 5- 30V
Net Weight: 15 grams
Dimensions: 22.0mm X 25.0mm X 28.00mm
Exposure Brightness / exposure mode / gain
White Balance: Automatic tracking white balance
Day & Night Mode: Internal Automatic / Color Mode / B&W Mode
Video Settings: Contrast / Sharpness / Saturation / Digital Noise / Video Format (NTSC/PAL)
Language: Chinese/ English / Russian / Italian / German
Universal GPS Folding Antenna Mount is used to mount GPS device on the flight. GPS devices are most accurate if their antennas have a clear view of the sky.
GPS/Compass modules are also prone to the electromagnetic interference generated by motors, ESCs, and radio transmission equipment.
Given both of these factors, for the best possible performance, it makes sense to use an extended mount to position your GPS/Compass far away from the sources of interference and well above your multirotor.
This mount measures 16cm, which is more than tall enough for most installations. Best still, the mount can be quickly folded without any tools for transportation or storage.
CNC manufacturing, carbon fiber hole: 4.0mm
Antenna base section can be folded, light weight and small size, compact structure, easy to use, is playing an essential tool for multi-axis ..
The shaft hole is 4MM,
Baby screw top containing tear carbide consistent picture! Suitable high-grade multi-axis aircraft!
Product Name: 4-Axis GPS Foldable Antenna Holder Base
Color: Silver, Red
Material: Aluminum alloy + carbon fiber
Compatible device: Quadcopter
Functions: DJI signal bracket
Net weight: 30 g
Package weight: 40 g
FPV camera is one of the most important parts of the FPV setup on a quadcopter. Real-time video captured from FPV camera is sent to the pilot through a video transmitter.It doesn’t matter what video transmitter you are going to use, the image you see is only as good as your FPV camera. And at 1200TVL, you get amazing video even in low light situations.
Image Sensor: 1/3" CMOS
Horizontal Resolution: 1200 TVL
S/N Ratio: >60dB (AGC Off)
Electronic Shutter Speed: 1/50 ~ 100,000
Autogain Control (AGC): Yes
Backlight Compensation: Yes
Min. Illumination: 0.01 Lux / 1.2F
Power: 5- 40V
Net Weight: 5.3G
Dimensions: 19.0mm X 19.0mm X 19.00mm
We are PCI-DSS compliant and use 256 bit SSL encryption.
99% of our orders are shipped within 24 hours.
Use the contact form for bulk order quotes.
Call us (Weekdays)
+91 93183 94903
India: Rani Bagh, New Delhi 110034 +91 93183 94903
USA: 405, Kennedy Space Center, FL 32899 | +1 (321) 210-8472
Hong Kong: Unicorn Trade Centre, 127-131 Des Voeux Road, Central HK