sale
NX3 3D Flight Controller / Gyroscope Balancer for fixed wing aircrafts and RC Planes NX3 3D Flight Controller / Gyroscope Balancer for fixed wing aircrafts and RC Planes
NX3 3D Flight Controller / Gyroscope Balancer for fixed wing aircrafts and RC Planes from ₹ 2,189.99 ₹ 1,999.00
The NX3 3D flight controller features a micro design, small size, supports single aileron model, V-tail model, delta wing model and dual aileron (flaperons) aircraft - Can also be used for 2 - axis on jets using 2 servos for ailerons and a servo on the elevator or if the jet uses 2 servos only, one serving the left aileron and elevator, and the other servo serving the right aileron and elevator, it can be set to a delta wing. Features:Humanized design, independent potentiometer adjust for different axis sensitivityOptional - Three-mode switched from controller, 1 - normal stability mode, 2- gyro off mode, 3- calibration.   Specifications Input voltage: DC5 - 6V, directly connected to the ESC's BEC power supply can be use.Operating Current: 18mAWorking temperature: -20 Celsius to 85 CelsiusDimensions: 25 × 40mmNet Weight: 6.5g Resources Datasheet Tutorial
sale
Pixhawk Kit Pixhawk Kit
Pixhawk Kit from ₹ 7,289.99 ₹ 9,999.00
1. The advanced 32-bit ARM CortexM4 high-performance processors, can run NuttX RTOS real-time operating system;2. 14 PWM / servo output;3. Bus interface (UART, I2C, SPI, CAN);4. The integrated backup power and backup controller fails, the primary controller fails over to the backup control is safe;5. Provide automatic and manual modes;6. Provide redundant power input and failover;7. Multicolor LED lights;8. Provide multi-tone buzzer Interface9. Micro SD recording flight data; 10. Power module not included Specifications Microprocessor 1.32 2 MB flash STM32F427 Cortex M4, with hardware floating-point processing unit2. frequency: 168MHZ, 256K RAM3.32 STM32F103 backup coprocessor Sensor1.L3GD20 3-axis digital gyroscope 162.LSM303D 3-axis accelerometer 14 / Magnetometer3.MPU6000 6-axis accelerometer / magnetometer4.MS5611 precision barometer Interface1 .5 high voltage compatible UART 1, 2 with hardware flow control2. 2 CAN3.Spektrum DSM / DSM2 / DSM-X satellite receiver compatible input4.Futaba SBUS compatible inputs and outputs5.PPM Signal Input6.RSSI (PWM or voltage) Input7.I2C8.SPI9.3.3 and 6.6VADC input10. External MICRO USB Interface   Pixhawk Telemetry Kit includes: 1x 2.4.8 Pixhawk flight controller board with shell 1x Safety switch 1x Buzzer 1 x SD to MicroSD Card Adaptor 1x PPM encoder 1x I2C splitter expansion module and 1x I2C Line 1x Power Module and 1x PPM/SBUS Line ​1x Radio Telemetry Set with receiver/transmitter and 2x antenna 1x M8N GPS 1x T Plug power module 1x GPS holder 1x Shock absorber 1x OTG MicroUSB to USB adaptor 1x 0.96" OLED Display Module   Resources Datasheet Tutorial
Sold out sale
CC3D EVO CC3D EVO
CC3D EVO from ₹ 1,199.99 ₹ 1,499.99
With a function of being directly plugged into the satellite receiver(It needn't conversion cable) Powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM. 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer. Tiny 36mmx36mm 4 layer PCB for superior electrical noise reduction and flight performance. Software support for Windows, for mac and Linux. Direct high speed USB support with no drivers required, a truly plug and play device or spektrum satellite receiver support. Futaba S-BUS hardware support. Innovative Flexi-port technology for superior port flexibility. 4Mbits on-board EEPROM for configuration storage. FlexiportCopterControl also offers the innovative Flexi-port which provides either I2C  connectivity or a second serial port. Flexi-port gives CopterControl the flexibility to use either I2C and a single serial port or dual serial ports, according to your connectivity needs. Superior user experienceOpenPilot has tried to make your experience with the CC3D as easy and trouble-free as possible. Naturally for a high-end product, the hardware is complete; there is nothing to solder. The included RC harness allows you to connect any standard PWM receiver. All CopterControl boards are tested before shipping and come with bootloader already flashed. A standard mini-USB cable (not included) is used to load the latest firmware and configure everything for your unique airframe. Specifications 3-axis Gupports several common RC inputs: 6 PWM channels, combined PPM, for spektrum/JR DSM2, Supports several common RC inputs: 6 PWM channels, combined PPM, for spektrum/JR DSM2, DSMJ, for satellites, and Futaba S.Bus receivers. Simultaneous support for multiple receivers. ReceiverPort functions (configurable): 6 PWM input channels or combined PPM stream, 4 PWM output channels MainPort functions (configurable): serial telemetry (default), GPS, S.Bus, for spektrum/JR satellites FlexiPort (configurable): serial telemetry, GPS, for spektrum/JR satellites, or I2C peripherals (under development) 10 PWM outputs to servos or ESC's, or for camera stabilization Camera stabilization: supports up to 3-axis camera mounts with stabilization and manual control from any of configured receivers. Onboard USB connectivity for easy configuration. USB and serial telemetry and configuration Supported by powerful OpenPilot GCS 4 Mbit onboard memory 3C Quaternion based complementary filter running at 500Hz Resources Datasheet Tutorial  
-8% sale
ArduPilot APM2.8 ArduPilot APM2.8
ArduPilot APM2.8 ₹ 2,995.00 ₹ 3,240.00
APM 2.8 Multicopter Flight Controller is an upgraded version of 2.5, 2.6; with a Built-in Compass for FPV RC Drone. The sensors are exactly the same as the APM 2.6 flight controller; however, the module has the option to use the built-in compass an external compass via a jumper. This makes the APM 2.8 ideal for use with multi-copters and rovers. The APM 2.8 Multicopter Flight Controller is a complete open source autopilot system. This is the best selling technology that won the prestigious Outback Challenge UAV competition. It allows the user to turn any fixed, rotary-wing. In addition, it turns multirotor vehicle (even cars and boats) into a fully autonomous vehicle. meanwhile, it is capable of performing programmed GPS missions with waypoints. Specifications Model APM 2.8 Power supply LP2985-3.3. Port MUX (UART0, UART2, mnnI2, and OSD are optional, OSD is the defaulted output). Input Voltage (V) 12~16 VDC Sensors 3-Axis GyrometerAccelerometerHigh-performance Barometer Processor ATMEGA2560 and ATMEGA32U-2 Micro-SD Card Slot No Dimensions (mm) LxWxH 85 x 45 x 15 Weight (gm) 82 Shipment Weight 0.175 kg Shipment Dimensions 9 × 3 × 2 cm Tutorial  
Sold out
Openpilot Atom NANO CC3D Flight Controller for Drones Openpilot Atom NANO CC3D Flight Controller for Drones
Openpilot Atom NANO CC3D Flight Controller for Drones from ₹ 1,349.99
This CC3D Atom is about half the size of the regular OpenPilot CC3D, but with the same functionality. Now you can get all the great features and functionality of the full sized CC3D flight controller board but at about 1/2 the size! Specifications Item name: CC3D Atom/Mini CC3D/CC3D EVO Size:36*28mm Net Weight: 22 g Weight: 32 g Features: The CC3D provides a crisp feel when flying tricopters, quads, hexas, octocopters, and even fixed wing planes. Powerful STM32 32-bit micro-controller running at 90MIPs with 128KB Flash and 20KB RAM. 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer. 4 layer PCB for superior electrical noise reduction and flight performance. Software support for Windows, Mac and Linux. Direct high speed USB support with no drivers required. Spektrum satellite receiver support. Futaba S-BUS hardware support. Innovative Flexi-port technology for superior port flexibility. 4Mbits on-board EEPROM for configuration storage. This OpenPilot CC3D Atom board also includes a high quality, protective case. Resources Datasheet Tutorial
Sold out sale
SP Racing F3 Acro SP Racing F3 Acro
SP Racing F3 Acro from ₹ 2,399.99 ₹ 2,999.00
Racing F3 Flight Controller (SPRacingF3) was designed to give awesome flight performancebased on tried and tested sensors whilst also providing unparalleled I/O capabilities in a small and extremelylightweight form-factor using a next-generation CPU.The SPRacingF3 gives you all the features you need for the heart of your aircraft, whether you’re into FPV racing,acrobatic flying or aerial photography it’s perfect. Specifications • No compromise I/O. Use all the features all the time; e.g. Connect your OSD + SmartPort + SBus + GPS + LEDStrip + Battery Monitoring + Sonar + 8 motors - all at the same time!• On-board high-capacity black box flight log recorder - optimize your tuning and see the results of your setup withoutguesswork ( Deluxe).• Next-generation STM32 F3 processor with hardware floating point unit for efficient flight calculations and fasterARM-Cortex M4 core.• Stackable design - perfect for integrating with OSDs and power distribution boards.• 16 PWM I/O lines for ESCs, Servos and legacy receivers. 8 available on standard pin headers. 8 via sidemounted connectors.• Full support for OneShot ESCs for easy PID tuning and a sharper response.• Supports SBus, SumH, SumD, Spektrum1024/2048, XBus, PPM, PWM receivers. No external inverters required(built-in).• Dedicated output for programmable LEDs - great for orientation, racing and night flying.• Dedicated I2C port for connection of OLED display without needing flight battery.• Battery monitoring ports for voltage and current.• Sonar support for precision low-altitude hold.• Buzzer port for audible warnings and notifications.• Developer friendly debugging port (SWD) and boot mode selection, unbrickable bootloader.• Symmetrical design for a super tidy wiring.• Wire up using pin headers, JST-SH sockets or solder pads. Use either right-angled or straight pin-headers.• Barometer mounted on the bottom of the board for easy wind isolation.• Loop times up to ~2x as fast as previous-generation STM32F1 based boards.• Configuration of the flight controller via a cross-platform GUI (Windows/OSX/Linux).• Supports a variety of aircraft, tricopters, quadcopters, hexacopters, octocopters, planes and more.• Available in Acro and Deluxe versions.VariationsAcro: Standard model for racing/acro flying.Deluxe: Additional sensors for altitude and direction.SoftwareThe SPRacingF3 runs the open-source Cleanflight flight control (FC) software which has an ever-growing communityof friendly developers and users. Being open-source means that you too can contribute to the system.Cleanflight comes with a detailed manual that is reviewed and maintained by the Cleanflight developers andcommunity. No more out-of-date wiki pages and second-hand information. Resources Datasheet Tutorial
Sold out sale
SP Racing F3 Deluxe SP Racing F3 Deluxe
SP Racing F3 Deluxe from ₹ 3,299.99 ₹ 3,999.00
Racing F3 Flight Controller (SPRacingF3) was designed to give awesome flight performancebased on tried and tested sensors whilst also providing unparalleled I/O capabilities in a small and extremelylightweight form-factor using a next-generation CPU.The SPRacingF3 gives you all the features you need for the heart of your aircraft, whether you’re into FPV racing,acrobatic flying or aerial photography it’s perfect. Specifications • No compromise I/O. Use all the features all the time; e.g. Connect your OSD + SmartPort + SBus + GPS + LEDStrip + Battery Monitoring + Sonar + 8 motors - all at the same time!• On-board high-capacity black box flight log recorder - optimize your tuning and see the results of your setup withoutguesswork ( Deluxe).• Next-generation STM32 F3 processor with hardware floating point unit for efficient flight calculations and fasterARM-Cortex M4 core.• Stackable design - perfect for integrating with OSDs and power distribution boards.• 16 PWM I/O lines for ESCs, Servos and legacy receivers. 8 available on standard pin headers. 8 via sidemounted connectors.• Full support for OneShot ESCs for easy PID tuning and a sharper response.• Supports SBus, SumH, SumD, Spektrum1024/2048, XBus, PPM, PWM receivers. No external inverters required(built-in).• Dedicated output for programmable LEDs - great for orientation, racing and night flying.• Dedicated I2C port for connection of OLED display without needing flight battery.• Battery monitoring ports for voltage and current.• Sonar support for precision low-altitude hold.• Buzzer port for audible warnings and notifications.• Developer friendly debugging port (SWD) and boot mode selection, unbrickable bootloader.• Symmetrical design for a super tidy wiring.• Wire up using pin headers, JST-SH sockets or solder pads. Use either right-angled or straight pin-headers.• Barometer mounted on the bottom of the board for easy wind isolation.• Loop times up to ~2x as fast as previous-generation STM32F1 based boards.• Configuration of the flight controller via a cross-platform GUI (Windows/OSX/Linux).• Supports a variety of aircraft, tricopters, quadcopters, hexacopters, octocopters, planes and more.• Available in Acro and Deluxe versions.VariationsAcro: Standard model for racing/acro flying.Deluxe: Additional sensors for altitude and direction.SoftwareThe SPRacingF3 runs the open-source Cleanflight flight control (FC) software which has an ever-growing communityof friendly developers and users. Being open-source means that you too can contribute to the system.Cleanflight comes with a detailed manual that is reviewed and maintained by the Cleanflight developers andcommunity. No more out-of-date wiki pages and second-hand information. Resources Datasheet Tutorial  
-46% sale
Naze32 6 DOF Flight Controller for Multicopter Naze32 6 DOF Flight Controller for Multicopter
Naze32 6 DOF Flight Controller for Multicopter ₹ 1,779.99 ₹ 3,295.00
32 6DOF Flight Controller for Multirotor Quadcopter Drone Modern GUI for all operating systems, Base flight Configurator Extra bright LEDs Onboard USB for setup and configuration Modern 32-bit processor (STM32 F103) running at 3.3V/72MHz. Built-in FrSky telemetry converter Battery voltage monitoring Designed for use with small indoor or small to mid-sized outdoor multirotor crafts, or as a standalone camera stabilizer. Specifications Designed for use with small indoor or small to mid-sized outdoor multirotor crafts, or as a standalone camera stabilizer. The flight controller is extremely simple to set up, with configuration based on the familiar ''MultiWii'' software. Battery voltage monitoring Built-in FrSky telemetry converter Modern 32-bit processor (STM32 F103) running at 3.3V/72MHz. Onboard USB for setup and configuration Extra bright LEDs Modern GUI for all operating systems, Base flight Configurator Sensors: MPU6050 Width: 36mm Height: 36mm Net Weight: 6g Resources Datasheet Tutorial  

Secure Checkout

We are PCI-DSS compliant and use 256 bit SSL encryption.

Instant Dispatch

99% of our orders are shipped within 24 hours.

Bulk Orders

Use the contact form for bulk order quotes.

Call us (Weekdays)

+91 93183 94903
Airtel Money Amazon American Express Diners Club Freecharge Google Pay Maestro Mastercard MobiKwik Ola Money PayPal Paytm RuPay Visa