Drones

High quality, solid metal case Deliver high efficiency and constant power for a stable flight Low noise, low starting voltage, and low energy consumption Highly reliable and durable for long-lasting use Lightweight, easy to install Suitable for Tiny Whoop Package contains: 2CW 2CCW Designed for RC Racing Quadcopter Specifications Color: Silver Speed: 14300KV Operating Voltage 1.5-3.7V Max. Thrust:15g (Direct Drive) Load Current: 1.0A at 3.7V (Direct Drive) Lifetime Rating: 5-6 hours Shaft Diameter: 0.8mm Shaft Length: 5mm Wire Length: 70mm Plug: Micro-JST-1.25 Material: Plastic & Metal Can Size: 15x6x6mm/0.6x0.2x0.2inch Net weight: 8g Tutorial  

Digital LCD Screen: Easy to read LCD screen provides clear number readings. And Real Time Reading: The Watt Meter will continuously provide real time readings of the amps, volts, and watts after connection. Provides 8 Electrical Readings: Current (A), Voltage (V), Watts (W), Amp-hours (Ah), Watt-hours (Wh), Peak Amps (Ap), Minimum Volts (Vm), Peak Watts (Wp). High Precision: Measures 0-150 Amps, Resolution 0.01 Amps. Measures 0-60 volts, Resolution 0.01 volts. 0 - 6554W, resolution 0.1W. 0 - 65Ah, resolution 0.001Ah. 0 - 6554Wh, resolution 0.1Wh. Multifunction Tool: Verifies sufficient operating voltage under load. Prevents peak currents damaging battery, ESC, motors, wiring and connectors. Confirms proper battery charger operation (connect between your battery and charger). Individual cell balancing. Set cutoff voltages, check battery capacity health. Detect receivers and actual operating current so as to make sure whether an UBEC is needed.   Examples of uses: How Much Power Does my Fridge Use – with the Battery connected to the SOURCE side and Car Fridge (or other accessories) connected to the LOAD side. The Watt Meter shows the current into the Fridge, voltage, and power at the battery and accumulates the Ah and Wh while the fridge is running. How much charge is going into my battery – With a battery charger (or alternator) on the SOURCE side and the aux battery on the LOAD side, the Watt Meter shows the charging current into the battery, the voltage and charging power at the battery and accumulates the charge (Ah) and energy (Wh) into the battery. What is the output of my solar panel  – With a solar panel on the SOURCE side and solar regulator on the LOAD side, the Watt Meter shows the charging current into the regulator, the voltage and charging power at the solar panel and accumulates the charge (Ah) and energy (Wh) into the regulator. How much charge is my solar panel putting into my battery – Now with a solar regulator on the SOURCE side and battery on the LOAD side, the Watt Meter shows the charging current into the battery, the voltage and charging power at the regulator and accumulates the charge (Ah) and energy (Wh) into the battery. Specifications Operates voltage: 4.8V-60VOV with optional auxiliary batteryDimension (L*W*T): 8.3 x 4.2 x2.4cm/3.27"x1.65"x0.94"(approx)Measures:0-150A, resolution 0.01A;0-60V, resolution 0.01v;0-6554W, resolution 0.1w;0-65Ah,resolution 0.001An;0-6441Wh,resolution 0.1Wh;backlit LCD display Resources Datasheet Tutorial  

- Simple structure and lightweight, CNC aluminum alloy structure- Brushless motor direct drive- With anti-vibration rubber balls, easy to adjust- Compatible with Gopro 4 3, 2,1- With 3pcs 2804 160t motor- With 32bit Storm32 firmware gimbal controller, sensor- With motor protector which can help heat dissipation Strom32 Gimbal ControllerFeatures:- The controller can be used for building high-quality 3-axis camera stabilizing systems that can be mounted to UAV and for building handheld camera stabilizers.- This version of the controller is our new direction in the development of stabilizing solutions.- It will replace the previous 8-bit version of the SimpleBGC controller, keeping 100% back-compatibility, but adding the new functionality.- 32-bit MCU — ARM Cortex M4.- Effectively calculates the complex tasks for 3-axis stabilization,700 times/seconds gyro calculates- Allows camera control with the RC or analog joystick.- Use several switchable profiles for different modes of operation- Control Pitch or roll by PWM or receiver, supports a variety of RC protocols: PWM, Sum-PPM, Spektrum, and s-bus.- Use IMU1 and onboard IMU2 dual sensor module lock YAW accurately, stable performance- Support follow mode, lock mode, absolute mode, or speed mode. Specifications - Power supply: 9-15V(3-4S)- Drive current: Max.1.5A- Height: 11cm- Color: Black

Support OTG of Android Cellphones,and computer OTG. Antenna is 5.8G level ,not the cheap 2.4G level (whose range is very small and material is very cheap) like others. - I preprogram these radios to the correct bod rate so you can just connect them to your quadrino and start chaning PID's on the fly. - The 3DR Radio telemetry system is designed as an open source Xbee replacement radio set, offering a lower price, longer range and superior performance to Xbee radios. It's availabl in 915Mhz; and in the following configurations: serial board (for the air) and USB (for the ground). - The radio is a 2-way half-duplex wireless communication system with a standard TTL UART interface, based on HopeRF's HM-TRP data link modules, and custom firmware that improves upon the modules' original features and performance. - The SiK firmware includes a bootloader that permits radio firmware upgrades over the serial interface, and radio firmware with configurable parameters. Firmware upgrades and configuration are fully supported in the APM Mission Planner. Configuration is also possible through AT commands. Specifications - Very small size- Light weight (under 4 grams without antenna)- 915MHz- Receiver sensitivity to -121 dBm- Transmit power up to 20dBm (100mW / 250mW)- Transparent serial link- Air data rates up to 250kbps- MAVLink protocol framing and status reporting- Frequency hopping spread spectrum (FHSS)- Adaptive time division multiplexing (TDM)- Support for LBT and AFA- Configurable duty cycle- Built in error correcting code (can correct up to 25% data bit errors)- Demonstrated range of several kilometers with a small omni antenna- Can be used with a bi-directional amplifier for even more range- Open source firmware- AT commands for radio configuration- RT commands for remote radio configuration- Adaptive flow control when used with APM- Based on HM-TRP radio modules, with Si1000 8051 micro-controller and Si4432 radio module Resources Datasheet Tutorial  

Very strong and light weight.Long lasting and easy to installStable and Shock ProofPerfect for RC Quadcopter Multi-Copter Specifications Material: PC & FiberLength: 5.0 inchScrew Pitch: 4.0 inchCentral Hole Diameter: 5mmColor: Green red grey blackNet Weight: 52g Tutorial

Multirotor propellers offer excellent durability at a fantastic price, giving you better control of your multi rotor with more resilience to breakage.The props are supplied in packs of 2, with 1, CW rotation and 1, CCW rotation.There is a wide range of color options that can be mixed and matched to help with orientation. This is the perfect upgrade for any small multirotor. Specifications Hi-Performance Prop FPV 3 blade bullnose propeller 5040 CW/CCWSize: 5 x 4Hub inner diameter(ID): M5Hub thickness: 7mmWeight: 3.2gFit: 200, 210, 230, 250, 280, 320 frame etc Tutorial

Hi-Performance Prop FPV 3 blades bullnose propeller 5045 CW/CCW Specifications Size: 5 x 4.5 Hub inner diameter(ID): M5 Hub thickness: 7mm Weight: 5.85g/pc Material: Polycarbonate Fit: 200, 210, 230, 250, 280, 320 frame etc Package Contains 2 pairs

8060 are high efficiency propellers, made of strong fiberglass solving immature breakage and cracks. Made of high quality material, which is lightweight, durable, eco-friendly and uneasy to be broken. Provides stronger thrust, more safe and energy saving. Easy and convenient to install and remove off. Suitable for different paddle clips or bullets, propellers protectors and easy to use. Well balanced, fine workmanship and excellent performance, a perfect accessory for RC airplane. Specifications Type: 8060 Propellers Material: Nylon， fiberglass  Color: Black Size: 8 * 6inch Mounting Hole Diameter: 5mm / 0.2inch Tutorial

Color: White Material: Plastic Suitable for DJI Phantom 2 vision, also suitable for DJI Phantom 1 Specifications Type: Self-Tightening CW CCW Propeller Size: 24*11.5cm/9.4*4.5inch Hole Diameter: 0.8cm / 0.3inch Weight: 20.68g / Pair Package Content: 1 x CW Propeller 1 x CCW Propeller

Even when they are available at a price everyone can afford, their shocking performance is what makes everyone like them (except A2212, at this price no Brushless Motor in the Market will give you the thrust around 700gm in flight). The low price of this motor is recognized with its low-quality bearings and magnets. This motor produces noise and vibration. Also, they become warm while operating at high speed. But all these shortfalls are negligible and doesn’t affect the performance of the motor. Package Contains: 1x A2212 motor. Specifications - Mode:Wester A2212- KV: 930 / 1000 /1400 /2200 according to your order- Max Efficiency: 80%- Max Efficiency Current: 4-10A (>75%)- Current Capacity: 12A/60s- No Load Current @ 10V: 0.5A- No. Of Cells: 2-3 Li-Poly- Motor Dimensions: Φ27.5 x 30mm- Shaft Diameter: Φ3.17mm- Weight: 47gXXD A2212 1000KV brushless outrunner motor:KV: 1000Max. efficiency: 80%Max. efficiency current: 4-10A (>75%)Current capacity: 12A/60sNo Load current @ 10V: 0.5ANo. of cells: 2-3 Li-PolyMotor size: 27.5 * 27mm / 1.1 * 1.1inShaft diameter: 3.17mm / 0.1inWeight: 48g / 1.7ozXXD A2212 1400KV brushless outrunner motor:- Shaft diameter: 3.17mm- Dimension : 27.8mm x 27mm- Recommended Propeller: 2-cells 7*3.5 , 3-cells 6x3- Weight: 48gXXD A2212 2200KV brushless outrunner motor:Max Efficiency: 80%Max Efficiency Current: 4-10A (>75%)Current Capacity: 12A/60sNo Load Current @ 10V: 0.5ANo. Of Cells: 2-3 Li-PolyMotor Dimensions: ?27.5 x 30mmShaft Diameter: ?3.17mmWeight: 47gXXD A2212 2700KV brushless outrunner motor:Rpm/V: 2700KVNet Weight: 50gWeight: 60gMotor Dimensions: 27* 26mmBattery Opernating: 2-3 LipoIdle current: 1.8ALoad current: 18.5APower (Watt): 240ESC(A): 30A,20APeak.Amps :14-22 A Resources Datasheet Tutorial

High quality aluminum material. Suitable for brushless motors and speed controllers.Manufactured with accurate workmanship. Package Includes: 1x Propeller Adaptor Specifications Color: Silver Material: Aluminum Variants 6mm to 4mm - Aperture: 4.0 (Motor Shaft) & Output Shaft Diameter: 6mm 6mm to 3.17mm - Aperture: 3.17 (Motor Shaft) & Output Shaft Diameter: 6mm 6mm to 3mm - Aperture: 3.0 (Motor Shaft) & Output Shaft Diameter: 6mm 5mm to 3.17mm - Aperture: 3.17 (Motor Shaft) & Output Shaft Diameter: 5mm 5mm to 3mm - Aperture: 3.0 (Motor Shaft) & Output Shaft Diameter: 5mm